INTEL 82578DC GIGABIT NETWORK CONNECTION DISABLE REENABLE DRIVER

The driver can limit the amount of interrupts per second that the adapter This information is accessed by the hardware. TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay parameters, see theĭescriptor describes a data buffer and attributes related to the dataīuffer. The default value for each parameter is generally the recommended setting, unless otherwise noted.įor more information about the AutoNeg, Duplex, and Speed parameters, see theįor more information about the InterruptThrottleRate, RxIntDelay, In this case, there are two network ports supported by igb in the system. Modprobe igb InterruptThrottleRate=16000,16000 The values will be applied to each instance, in function order. There needs to be a for each network port in the system supported by this driver. If the driver is built as a module, the following optional parameters are used by entering them on the command line with the modprobe command using this syntax: If your kernel supports DCA, the driver will build by Interrupts in cat /proc/interrupts for the ethX igb device, then this Normally the driver will generate an interruptĮvery two seconds, so if you can see that you're no longer getting System needs to disable this style of interrupt, the driver can be built Trouble supporting MSI and/or MSI-X interrupts. Is the IP address for another machine on the same subnet as the interface

INTEL 82578DC GIGABIT NETWORK CONNECTION DISABLE REENABLE DRIVERS

With 2.6 based kernels also make sure that older igb drivers are removedįrom the kernel, before loading the new module:Īssign an IP address to the interface by entering theįollowing, where is the interface number: This may differ for various Linux distributions.

INTEL 82578DC GIGABIT NETWORK CONNECTION DISABLE REENABLE INSTALL

The install location listed above is the default location. lib/modules//kernel/drivers/net/igb/igb.o Untar/unzip the archive, where is the version number for the driverĬhange to the driver src directory, where is the version number for the driver For example, use '/home/username/igb' or '/usr/local/src/igb'. Move the base driver tar file to the directory of yourĬhoice. Recompiled the kernel reboot the system now. MUST match the version and configuration of the installed kernel sources. To build a binary RPM* package of this driver, run 'rpmbuild -tbįor the build to work properly, the currently running kernel Updating ethtool can be found in the section Additional Later), lspci, and ifconfig to obtain the same information. Alternatively, you can use ethtool (version 1.6 or The driver information previously displayed in the /proc file system is not

The igb driver supports IEEE 1588 time stamping for kernels 2.6.30 and above. The following features are now available in supported kernels:Ĭhannel Bonding documentation can be found in the Linux kernel source: Hardware requirements listed apply to use with Linux. To hardware requirements, refer to the documentation supplied with your Intel Patches against the kernel source to allow for static linking of the drivers. These drivers are only supported as a loadable module. These drivers includes support for Itanium® Support the 2.4.x, 2.6.x, and 3.x kernels.

INTEL 82578DC GIGABIT NETWORK CONNECTION DISABLE REENABLE HOW TO

Then select the name of the specified base driver: igb or e1000e.įor more information on how to identify your adapter, go to the Adapter & Driver ID Guide at:įor the latest Intel network drivers for Linux, refer to the following website. Setup/system-config-network or SuSE's yast2.įirst identify your adapter. Specific method for configuring network adapters like RedHat's

Modify /etc/nf to point your PCIe devices to use the newĮ1000e driver using alias ethX e1000e, or use your distribution's.

Install the e1000e driver using the instructions in the.

INTEL 82578DC GIGABIT NETWORK CONNECTION DISABLE REENABLE UPGRADE

If your version of e1000 is 7.6.15.5 or less, upgrade to e1000.UPGRADING: If you currently have the e1000 driver installedĪnd need to install e1000e, perform the following: Then follow the appropriate steps for building, Is supported by the e1000 driver, not the e1000e due to theĨ2546 part being used behind a PCI Express bridge. NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter NOTE: As of July 2012, the e1000 legacy driver is no longer supported and is only maintained through the upstream kernel. e1000e driver supports all PCI Express gigabit network connections,Įxcept those that are 82575-, 82576-, 82580-, and I350-based.The igbvf driver supports 82576-based virtual function devices thatĬan only be activated on kernels that support SR-IOV.NOTE: This release includes the following Linux* Base Drivers for Linux Driver for Intel® Gigabit Network Connections Linux* Base Drivers for Intel® Ethernet Network Connection

Intel 82578dc gigabit network connection disable reenable